Product ID:HOT MELT ADHESIVE, 61-1100
MSDS Date:07/12/1990
FSC:8040
NIIN:00N042793
MSDS Number: BRPWG

WORTHEN INDUSTRIES

3 EAST SPIT BROOK RD
NASHUA, NH 03060
US

Emergency Phone: 800-424-9300(CHEMTREC)

Info Phone: 603-888-5443

Cage: 56612

WORTHEN INDUSTRIES

NASHUA, NH 03060 US

Telephone: 603-888-5443

Cage: 56612

BENZENEPROPANOIC ACID, 3,5-BIS(1,1-DIMETHYL)-4-HYDROXY-,

CAS: 6683-19-8

RTECS: DA8340900

OSHA PEL N/K

ACGIH TLV: N/K

ING 3

RTECS: 9999999ZZ

EVA COPOLYMER

CAS: 24937-78-8

OSHA PEL N/K

ACGIH TLV: N/K

THERMOPLASTIC HYDROCARBON RESIN

CAS: 9011-11-4

OSHA PEL N/K

ACGIH TLV: N/K

PARFAFFIN WAX

CAS: 64742-43-4

OSHA PEL N/K

ACGIH TLV: N/K

PARAFFIN; (SYNTHETIC WAX)

CAS: 8002-74-2

RTECS: RV0350000

OSHA PEL N/K

ACGIH TLV: N/K

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:ACUTE/CHRONIC: INHAL IS NOT POSS IF
MATL IS IN SOLID FORM. IF MOLTEN, OVEREXP WILL CAUSE A HDCH. EYES:
SOLID MATL HAS NO EFT. MOLTEN MATL WILL IRRITATE & BURN IF IN
DIRECT CONT. SKIN: SOLID MATL HAS N O EFT. MOLTEN MATL WILL BURN
UNTIL POLYMER IS COOL. INGEST: SOLID MATL HAS NO EFT. MOLTEN MATL
WILL (EFTS OF OVEREXP)
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:HLTH HAZ: BURN INTENSELY. IF PERSONAL CONT
W/MOLTEN MATL PRDCES A BURN SEE A PHYS/BURN CTR IMMED. INHAL: INHAL
OF MOLTEN MATL FUMES MAY RSLT IN A HDCH IF INSUFFICIENT VENT.
SKIN/EYE: MOLTEN MATL WILL CAUSE SEV EYE DAM IF CONT OCCURS.
FUMESFROM MOLTEN MATL MAY CAUSE SOME IRRIT IF ADEQ VENT IS NOT
USED. (SUPP DATA)
Medical Cond Aggravated by Exposure:HEADACHES.

First Aid:INHAL: REMOVE TO FRESH AIR. EYES: RINSE W/ COLD WATER IMMED
FOR @ LST 15 MIN & SEE A PHYS IMMED. SKIN: IMMED SUBMERGE BURNED
SKIN AREA IN COLD CLEAN WATER. DO NOT ATTEMPT TO PULL AWAY
SOLIDIFIED MATL ADHERING TO SKIN. SEK MED ATTN. INGEST:BRING TO
HOSP IMMED. MATL @ ROOM TEMP IS A SOLID MATL BUT IS NORMALLY USED
AS A HOT MELT, SO TREAT ANY PERSONAL CONT W/MOLTEN MATL AS A NORMAL
BURN.

Flash Point:<400F,<204C
Extinguishing Media:FOAM, CARBON DIOXIDE, DRY CHEMICAL.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA AND FULL
PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:COOLING WITH WATER WILL SOLIDIFY THE
MATERIAL VERY RAPIDLY. NO UNUSUAL FIRE AND EXPLOSION HAZARDS ARE
KNOWN.

Spill Release Procedures:NORMAL HOUSEKEEPING FOR SOLID MATL. CLEAN
MACHINERY OF RESOLIFIED MATERIAL WITH SOLVENT, TAKING CARE TO
ELIMINATE ALL HEAT AND SPARK SOURCES. FOR LARGE SPILLS OF MOLTEN
LIQUID, ALLOW TO SOLIDIFY AND S CRAPE UP.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:NOT APPLICABLE IN SOLID FORM. REVIEW
EMERGENCY AND FIRST AID PROCEDURES BEFORE HANDLING MOLTEN
MATERIALS.
Other Precautions:NONE IN SOLID FORM.

Respiratory Protection:NOT REQUIRED FOR NORMAL USAGE CONDITIONS WITH
ADEQUATE VENTILATION. USE NIOSH/MSHA APPROVED RESPIRATOR
APPROPRIATE FOR EXPOSURE OF CONCERN .
Ventilation:LOCAL EXHAUST IF USED IN A CONFINED AREA. MECHANICAL
VENTILATION REQUIRED FOR LARGE VOLUME USE.
Protective Gloves:IMPERVIOUS GLOVES .
Eye Protection:CHEMICAL SAFETY GOGGLES .
Other Protective Equipment:FULL BODY COVERING CLOTHES IF SPLASHING OR
SPRAYING THE MOLTEN MATERIAL.
Work Hygienic Practices:ALWAYS HANDLE CHEMICALS W/CARE. BE SURE TO HAVE
EYE RINSE AND SHOWER STATION W/IN THE WORKING AREA.
Supplemental Safety and Health
EFTS OF OVEREXP: SKIN ABSORP: MOLTEN MATL WILL CAUSE INTENSE SKIN BURNS
AS WOULD ANY OTHER MOLTEN THERMOPLASTIC MATL. INGEST: SHOULD INGEST
OCCUR, MOLTEN POLYMER WILL BURN INTERNAL ORGANS SEVERELY. SO LID
MATL IF INGESTED WILL CAUSE NO DAMAGE AT ALL.

HCC:N1
Vapor Density:HVR/AIR
Spec Gravity:0.8(H2O=1)
Evaporation Rate & Reference:Solubility in Water:NONE
Appearance and Odor:CLEAR TO AMBER SLATS OR PELLETS

Stability Indicator/Materials to Avoid:YES
NONE.
Stability Condition to Avoid:NONE.
Hazardous Decomposition Products:ON THERMAL DECOMPOSITON IT MAY EMIT
TOXIC FUMES, INCLUDING CARBON MONOXIDE AND OR CARBON DIOXIDE.

Waste Disposal Methods:NORMAL DISPOSAL FOR SOLID WASTE AS MIGHT BE USED
FOR OTHER PLASTIC MATERIALS SUCH AS POLYETHYLENE. DISPOSE OF I/A/W
ALL LOCAL, STATE AND FEDERAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.